多胞材料的力学行为

多胞材料具有独特的力学性质,其工程应用日益增加.人造多胞材料可以分为蜂窝材料和泡沫材料两类.本文介绍了这两类材料在不同载荷条件下力学行为的研究概况.对于某些天然材料(木材和松质骨)的多胞结构及其模型也作了简要介绍.     

任意三维贮箱内液体晃动的模态分析及其等效力学模型

本文采用有限元方法建立了数值求解任意三维贮箱内液体晃动固有频率和摸态、动力特征参数的通用程序，利用ANSYS有限元前处理模块．使得程序的通用性达到最大化。通过对液体受迫晃动的结果分析，发现了三维晃动中贮箱外激励与模态响应之间的复杂关系．并且提出了建立液体受迫晃动的等效力学模型的方法。本文以油罐车充液贮箱为例，数值研究了贮箱端部不同所引起的动力学差异，给出了晃动频率和晃动质量的变化曲线。     

局部荷载作用下网架结构的拟夹层板分析法

把正交正放类网架结构简化为构造上正交异性的夹层板，采用考虑剪切变形的具有三个广义位移的平板弯曲理论来分析，给出了网架结构在局部荷载作用下的内力、位移解析计算公式，并用有限元方法进行了验证．     

初弯曲纵横弯曲梁的等效载荷法及其应用

介绍一种求解初弯曲纵横弯曲梁的方法——等效载荷法,以及该方法在解决实际工程问题中的成功应用,为井下控制工具的研制和井眼轨道控制提供了理论依据．     

On the equivalence of the Wilson element and the generalized hybrid element

In this paper the equivalence of the generalized hybrid element and the modified Wilson element, which is derived by the generalized hybrid method, is proved. The project is supported by the National Natural Science Foundation of China     

A delta-function method for the n-th approximation of relaxation or retardation time spectrum from dynamic data

A function series g(x; n, m) is presented that converges in the limiting case n and m = constant to the delta-function located at x = = 1. For every finite n, there exists 2n+1(–nmn) approximations of the delta-function _(n)(x–x _n,m ). x _n,m is the argument where the function reaches its maximum. A formula for the calculation is given.The delta-function approximation is the starting point for the approximative determination of the logarithmic density function of the relaxation or retardation time spectrum. The n-th approximation of density functions based on components of the complex modulus (G*) or the complex compliance (J*) is given. It represents an easy differential operator of order n.This approach generalizes the results obtained by Schwarzl and Staverman, and Tschoegl. The symmetry properties of the approximations are explained by the symmetry properties of the function g(x; n, m). Therefore, the separate equations for each approximation given by Tschoegl can be subsumed in a single equation for G and G, and in another for J and J.     

Viskositätsmessung mit dem longitudinal schwingenden Band

A method for the detection of small masses with the aid of a longitudinally vibrating band is described and further applications, e.g. for viscosity and humidity measurement are discussed. The complex Young's modulus of the band can also be determined.

     

Forced oscillations of a layer of a viscoelastic material under the action of a convective pressure wave

The longitudinal and transverse components of deformation of the surface of a flat layer of a viscoelastic material glued onto a solid base under the action of a traveling pressure wave are determined. The coating compliance is described by two components corresponding to two components of surface displacement. The dimensionless compliance components depend only on the viscoelastic properties of the material, the ratio of the wave length to the layer thickness λ/H, and the ratio of the wave velocity to the velocity of propagation of shear oscillations V/C _t ⁰ . Data on the dynamic compliance are presented for 0.3 < λ/H < 30 and 0.1 < V/C _t ⁰ < 10. The compliance is demonstrated to be determined by its absolute value and by the phase lag of strain from pressure. The effect of viscous losses in the material and compressibility of the latter on the dynamic compliance is analyzed. An anomalous behavior of the compliance with the wave velocity being greater than a certain critical value is explained. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 48, No. 2, pp. 90–97, March–April, 2007.     

Indentation tests investigation of mechanical behavior of two-dimensional materials

准确了解二维材料的力学性能对于推动其应用具有重要意义, 无基底压痕技术是目前最广泛采用的二维材料力学性能测试方法之一, 本文综述了二维材料压痕研究的最新进展以及所面临的问题, 并对将来的研究工作进行了展望.无基底压痕技术是将二维材料转移到带有沟槽或柱形孔的基底上, 制备二维材料"梁"和"鼓"模型, 然后利用原子力显微镜测量其在压针作用下的载荷--位移关系, 最后通过基于连续介质薄膜导出的压痕响应分析模型拟合实验结果, 估算出二维材料的弹性模量和本征强度.由于二维材料的厚度远小于连续介质薄膜, 来自于压头以及基底孔侧壁的范德华力对二维材料的压痕响应具有显著影响, 造成二维材料与传统压痕分析模型中的基本假设不符, 导致不能准确预测二维材料的弹性模量; 另外, 由于传统压痕模型无法准确描述二维材料在大变形下的非线性行为, 以及由缺陷等引起的应力集中, 导致由压痕测试表征的二维材料(特别是多晶二维材料)本征强度具有较大的偏差. 因此, 一方面需要正确了解由压痕技术获得的二维材料力学性能, 另一方面还需对目前的研究方法做进一步的改进和完善.     

A molecular mechanics approach for analyzing tensile nonlinear deformation behavior of single-walled carbon nanotubes

In this paper, by capturing the atomic information and reflecting the behaviour governed by the nonlinear potential function, an analytical molecular mechanics approach is proposed. A constitutive relation for single-walled carbon nanotubes (SWCNT’s) is established to describe the nonlinear stress-strain curve of SWCNT’s and to predict both the elastic properties and breaking strain of SWCNT’s during tensile deformation. An analysis based on the virtual internal bond (VIB) model proposed by P. Zhang et al. is also presented for comparison. The results indicate that the proposed molecular mechanics approach is indeed an acceptable analytical method for analyzing the mechanical behavior of SWCNT’s. The project supported by the National Natural Science Foundation of China (10121202, 90305015 and 10328203), the Key Grant Project of Chinese Ministry of Education (0306) and the Research Grants Council of the Hong Kong Special Administrative Region, China (HKU 7195/04E).